Automated HVAC take-off software
AI measures the tender. Your estimators set the price.
AI HVAC take-off that reads the whole tender: drawings, schedules and specification. Customiser measures the ductwork, counts the equipment, fittings, dampers, terminals and pipework on every sheet, shows where each number came from and lists the questions to raise before you price.
More tenders land than your team has hours to measure
Every run traced by hand.
Duct measured run by run with a scale rule or a PDF tool, fittings and dampers tallied with a highlighter, sheet after sheet.
The spec read at the end, if at all.
Hundreds of pages of particular and workmanship specification, where the damper types, gauges and access rules that change the price are buried.
Questions found on site, not at tender.
A size printed but not drawn, a drawing referenced but not issued, scope marked by specialist: missed at tender, paid for later.
More tenders than estimators.
Every bid you pass on because nobody had the two days to take it off is work a competitor wins.
What it does
From the tender e-mail to the RFI register
Six parts of one HVAC estimating workspace: the take-off, the specification check, RFIs, submittal review, a tender inbox and an archive of every past job.
- Take-off
The whole drawing set, measured.
Automatic HVAC take-off from the drawings as issued: equipment, ductwork by system, size and gauge, fittings, dampers, grilles, diffusers, terminal units, attenuators, access doors, plant connections and pipework. Every sheet is read, and every quantity is tied to the spot on the drawing it came from.
- Systems read from the drawing's own colour key
- Runs measured along their centre lines at the sheet's scale
- Sizes printed on the drawing read; measured ones held as provisional
- Specifications
Spec clauses read, not skimmed.
Particular and materials-and-workmanship specifications are broken into numbered clauses. Every clause that moves a ductwork price is cited with its page and compared with the drawings, so a gap or a contradiction shows up while you can still ask about it.
- Materials, gauges, dampers, access doors, insulation, finishes, testing
- Each requirement quoted with its clause and page
- Sizes printed but not drawn, drawings referenced but not issued
- RFIs
Gaps turned into RFIs.
Whatever the drawings and the specification leave unsettled becomes a finding with its evidence, raised as an RFI in the tender's register for your team to approve and send.
- Fire damper types the spec does not settle
- Scope marked by specialist or by others, listed for your scope letter
- One RFI register per tender
- Submittals
Product data reviewed clause by clause.
Each manufacturer data sheet is read against the clause it is meant to satisfy. Anything that falls short or is missing goes on a list for your project engineer before the submittal is returned.
- Each check cites the clause it was made against
- Deviations and gaps listed, not buried
- Tender inbox
E-mail in, take-off underway.
A teammate forwards the tender e-mail with its drawings and specification, and Customiser files it as a tender and starts the take-off straight away.
- No upload step for your estimators
- Every tender in one list, with its client and due date
- Job archive
What you learned last time, on hand.
Previous tenders, their quantities and their findings are kept together, so a new bid can start from the decisions your team made on similar jobs.
- Search across past tenders and their take-offs
- Findings from earlier jobs one search away
Take-off
Every number shows its source
Open any line of the take-off and the drawing opens where it was found. A size read from the scale rather than printed on the sheet is marked provisional until someone on your team signs it off.
Duct by system, size and gauge.
Each system read from the drawing's colour key, its ducts measured along their centre lines and joined into runs, with the sheet thickness from DW144 or your own table.
Fittings, dampers and terminals counted.
Bends, branches and reducers; fire, fire and smoke, volume control, motorised and non-return dampers; grilles, diffusers, disc valves, attenuators, flexible connections, plant connections and piping.
Access doors by rule.
Access doors placed by the TR19 and DW144 default, both sides of dampers and attenuators, or by the rule your spec sets, each one sized for its duct.
Spec clauses matched to the drawings.
Clauses that affect price, from gauges to dampers and insulation, are cited with their page and checked against the layouts. Disagreements become findings and draft RFIs.
Every quantity traceable.
Each line opens the drawing at the spot it was taken from. Printed sizes are marked as read; sizes scaled off the sheet stay provisional until your team signs them off.
Exports your estimators already use.
The schedule of quantities exports to Excel, shaped to your template, ready to price in your estimating system or your own sheet.

Documents it reads
The tender as it arrives
- Ventilation layouts
- Mechanical drawing sets
- Colour keys and legends
- Duct and fitting schedules
- Equipment schedules
- Particular specifications
- Materials and workmanship specs
- Tender e-mails
- Submittals
- Past tenders
Who it is for
Built for the people who price air
Ductwork contractors
Supply and install, low and medium pressure, fire-rated ductwork: the full schedule of quantities your estimating system prices.
Mechanical contractors
The air side of a mechanical bid taken off, with the spec checked and the open questions raised before the tender closes.
Duct fabrication shops
Sizes, gauges and fittings read from the layout, so the shop knows the metal before the order lands.
Security
Your drawings stay yours
Your team reviews every number, and Customiser sends nothing out on its own.
Walled-off workspaces
Each company has its own workspace. Postgres row-level security, applied in the database rather than only in application code, stops any other workspace from reading your tables.
Your IP stays yours
Drawings, specs, take-offs and quotes belong to you. We hold a licence only to run the service for you.
Kept out of model training
Customiser does not train AI models on what you upload, and our model provider's terms forbid it from doing so either.
VENTILATION LAYOUTS · MECHANICAL SETS · DUCT AND EQUIPMENT SCHEDULES · PARTICULAR SPECS · WORKMANSHIP SPECS · DW144 · TR19 · SMACNA · FIRE DAMPERS · ACCESS DOORS · PIPING · RFIS · EXCEL BoQ
FAQ
Automated HVAC take-off: questions, answered
Straight answers on documents, pricing and how quotes are built. Anything else, ask us.
Contact usIt is AI software that turns mechanical and ventilation drawings into a quantity take-off without manual measuring: ductwork by system, size and gauge, plus equipment, fittings, dampers, grilles, diffusers, terminal units, plant connections and piping, counted across every sheet. Customiser also reads the specification, checks it against the drawings and drafts RFIs for what the documents leave open. Your estimators review the quantities and price the job.
Yes. Send the drawings and the specification, by upload or by forwarding the tender e-mail, and the whole take-off is produced without anyone picking symbols or tracing duct. Your estimators review the flagged items and set the price.
Open any line and the drawing opens where that item was found, so a check takes seconds instead of a re-measure. Sizes printed on the sheet are marked as read; sizes scaled from the drawing stay provisional until confirmed, and each line shows how much of its length is provisional.
No. Customiser produces the schedule of quantities and the drawing references behind each line; pricing stays in Ensign, QuoteSoft, Trimble or whatever your estimators use. Export to Excel in your template, or connect by API to your quoting software or ERP.
Yes. Particular and materials and workmanship specifications are split into their numbered clauses. The clauses that change a ductwork price (materials and gauges, dampers, access doors, flexible ducts, insulation, finishes, testing) are quoted with their page and checked against the drawings, and anything that disagrees becomes a finding.
Your own. Sheet thickness defaults to the DW144 table and access doors to the TR19 and DW144 rule, and both are defaults a company replaces with its own tables, including SMACNA gauges for North American work. The rule used is shown next to each line.
Items marked by specialist, by others or by the main contractor are recognised on the plans, left out of your quantities and listed separately for your scope letter.
No. Customiser does not size duct or calculate loads. It reads what the engineer has drawn and specified and turns it into a take-off your estimators can price.
No. Uploads stay in your own workspace, protected by row-level security in the database and encrypted at rest, and Customiser does not train AI models on them. The ductwork reader is our own code and makes no AI model call.
Book a demo and bring a recent tender. For teams, our forward-deployed engineers load your gauge tables, access rules and export template, and you run live tenders within about three weeks.
Send us one tender
A ventilation layout and its specification, as the consultant issued them. We will show you the take-off, the findings and the RFIs that come back.
Book a demo (opens in a new tab)Read next
How to do a ductwork takeoff
The manual method step by step, and the parts of it software now does.
Security and deployment
Database-level separation, your IP, no training, and forward-deployed engineers.
Sheet metal and fabrication
Cuts, bends, holes and finishes read from sheet metal packages and priced with your rates.
How does quoting from 2D drawings work?
Title block, dimensions and feature tables: how a clean drawing becomes a feature list.
How is a BOM extracted from a drawing package?
Tables, parts lists and multi-sheet assemblies: reconciling a BOM from wherever it actually lives.
What are labour standards and rate cards?
What the two actually are, and why consistent application matters more than the numbers.

