Estimating
Automated HVAC Takeoff Software: Manual, On-Screen and AI Takeoff Compared
Automated HVAC takeoff software reads your mechanical drawings and counts the duct, fittings, dampers and terminals itself. Here is how it compares with manual and on-screen takeoff, and how to judge one.
Customiser team5 min read
Key takeaways
- Automated HVAC takeoff software reads the drawings and returns the quantities; the estimator checks and prices them instead of clicking every run.
- On-screen takeoff tools are faster than paper, but a person still picks every run and symbol.
- Judge an automated tool by its evidence: every quantity should link back to the place on the drawing it came from.
- The best tools also read the specification against the drawings and draft RFIs for what is unclear.
- Ask where your drawings are stored, who can see them and whether they are used to train AI models.
HVAC estimators spend much of their week counting. Duct by size and gauge, bends and branches, fire dampers, grilles and diffusers: every sheet, every revision. Takeoff software exists to cut that time, but tools differ a great deal in how much of the counting they actually do.
Automated HVAC takeoff software reads mechanical drawings itself and returns a schedule of quantities, duct by system, size and gauge, fittings, dampers, terminals and plant connections, with each quantity linked to where it was found. On-screen takeoff software, by contrast, measures what an estimator clicks. The first changes the estimator's job from counting to checking; the second makes counting faster.
What are the three ways to do an HVAC takeoff?
| Manual (paper) | On-screen takeoff | Automated takeoff | |
|---|---|---|---|
| Who counts | The estimator, with a scale rule | The estimator, clicking on a PDF | The software; the estimator checks |
| Typical tools | Highlighters, scale rule, spreadsheet | PlanSwift, Bluebeam Revu, duct-specific tools such as QuoteSoft Duct and Trimble FastDUCT | AI takeoff tools that read the drawing |
| Spec reading | By hand | By hand | Some tools read the spec against the drawings |
| Evidence | Marks on paper | Marks on the PDF | Each quantity linked to its place on the sheet |
| Best for | Small jobs | Teams with time to click every run | Teams bidding more work with the same estimators |
What should "automated" actually mean?
Many tools call themselves automated because they count one symbol after you teach it, or because they measure a run once you click its ends. A fully automatic HVAC takeoff should do the following without an estimator pointing at anything:
- Read the legend or colour key to tell supply from extract, fresh air and exhaust.
- Measure duct runs along their centre lines at the sheet's scale, by size and gauge.
- Read printed sizes and mark any size it had to measure as provisional, not as fact.
- Count fittings, dampers, terminals and ancillaries by type and size across every sheet.
- Read the specification and flag where it conflicts with the drawings or leaves scope unsettled.
- Draft RFIs for the open questions, for your team to approve and send.
- Export a schedule of quantities your estimating system can take in, usually as Excel.
How do you check an automated takeoff?
Do not judge a tool by a headline accuracy figure. Judge it on your own drawings: send it a past tender you have already priced and compare.
- 1
Pick a past tender
One you priced and know well, ideally with a mix of systems, fire dampers and a written specification.
- 2
Compare by item, not by total
A total can match while fire dampers are under-counted and grilles over-counted. Compare item by item.
- 3
Click through the evidence
Every quantity should open the drawing at the place it was counted. If it cannot show you, you cannot check it.
- 4
Look at what it flagged
Provisional sizes, spec conflicts and missing drawings are worth as much as the counts.
- 5
Time the check
The measure that matters is how long your estimator takes to check and price, against how long the takeoff took before.
What should you ask an HVAC takeoff software vendor?
- Does it read our drawings as issued, PDFs and scans, or only clean CAD?
- Which standards does it apply for gauge and access doors (DW/144, TR19, SMACNA), and can we set our own?
- Does it read the specification, and does it quote the clause and page for each requirement?
- Can our estimating system take its export without retyping?
- Where are our drawings stored, who can see them, and are they used to train AI models?
- Who sets it up for our standards, and how long until our team is using it on live tenders?
How Customiser does it
Customiser reads ventilation layouts, legends, schedules and the specification together. It returns the duct by system, size and gauge, the fittings, dampers, terminals, ancillaries and plant connections, each linked to the place on the drawing it came from; it checks the specification against what is drawn and drafts the RFIs. Your drawings are never used to train AI models. See automated HVAC take-off for how it works and how a team goes live.
